Previous product
endurance test device for appliance
Endurance Test Device For Appliance Switches
Back to products
Next product
pressure immersion tank
Pressure Immersion Tank for IPX8
current source
current source
Click to enlarge

Current Source

Current Source provides the required test current for heating tests in IEC 60884-1, IEC 60320-1 and similar standards.

Teklif Al
SKU: MT-LP901E, MT-LP902E Category:
Description

Features

It is used in the tests of power cables and electrical materials which must be tested at 50 A / 20 A. In tests with current flow only 2 (LP-901) or 6 (LP-902) samples can be tested. The output voltage of the device can be adjusted.

Teknik Parametreler

Power Supplay AC 220 V ± % 5, 50 Hz
Output Current 0~40 A isteğe göre ayarlanabilir
Output Voltage 0~280 V
Test station 2 (LP-901); 6 (LP-902)
Ammeter accuracy % ± 1
Ambient temperature – 10 ℃~50 ℃
Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Current Source”

Your email address will not be published. Required fields are marked *

Related products

compression test apparatus in hot conditions
Close

Compression Test Apparatus in Hot Conditions

Compression Test Apparatus in Hot Conditions meets the standard of IEC 60884-1, Clause 25.4, Figure 38, It is designed to test the heat resistance of the accessories
Read more
Quick view
plug torque tester
Close

Plug Torque Tester

Plug Torque Tester meets the standards of EN/IEC 60065 Clause 15.4.1, Figure 11; IEC 60884-1 Clause 14.23.2 and EN/IEC 60335-1 Clause 22.3. It is designed to verify that appliances with contact pins for fixing to fixed socket-outlets cause excessive strain on these socket-outlets.
Read more
Quick view
apparatus for impact test
apparatus for impact test
Close

Apparatus for Impact Test at Low Temperature

Apparatus for Impact Test at Low Temperature meets the standard of IEC 60884-1 Clause 24.4 Figure 27 and Clause 30.4 Figure 42. It is used for low temperature mechanical impact test for plugs and portable socket-outlets with enclosures, covers or bodies of by made of elastomeric or thermoplastic material. In addition, this device is also used for low temperature impact test of pin-insulating sleeves.
Read more
Quick view
apparatus for compression test
Close

Apparatus for Compression Test

Apparatus for Compression Test meets the standard of IEC 60884-1 Clause 24.5, Figure 8.
Read more
Quick view
apparatus for verification
apparatus for verification
Close

Apparatus for Verification of Maximum Withdrawal Force

Apparatus for Verification of Maximum Withdrawal Force meets the standard of IEC 60884-1 Clause 22, Figure 18 and Figure 19. This tester is used to check whether the minimum force used to pull the single pin out of the socket-outlet with the maximum force applied to pull the plug out of the socket-outlet is within the allowed range in the standard.
Read more
Quick view
Load Bank
load bank
Close

Load Bank

Load Bank is designed and manufactured according to IEC 60884(Clauses 20 and 21), IEC 61058 (Clause 17), IEC 606691(Clauses 18 and 19) standards and etc. It is used for the on-off ability test and the normal operation lifespan test of the Switches for household and similar fixed-electrical installations. Besides, it is also applied in the test of breaking capacity of plug and socket-outlets, and mechanical action of normal operation lifespan.
Read more
Quick view
rotating barrel
rotating barrel
Close

Rotating Barrel

Rotating Barrel is intended for the Procedure 2- Free fall test described in EN/IEC 60068-2-31 clause 5.3.
Read more
Quick view
torque tester for cord
Close

Torque Tester For Cord Anchorages

Torque Tester For Cord Anchorages meets the standard of IEC 60884-1 Clause 23.2. Immediately after the tensile test of the flexible cables, the cord anchorage is exposed to the following torque for 1 minute.
Read more
Quick view